COSTA Industrial

Hot mix asphalt plant controls

ROVER &
ROVER LITE

Control the blend from one touchscreen. ROVER LITE handles aggregate feed, weighing, and asphalt metering. Choose ROVER if your mix also calls for an asphalt additive or mineral filler.

ROVER complete plant control console with touchscreen, operator controls and lower equipment cabinet
ROVER LITE complete console

01 / Featured system

ROVER & ROVER LITE plant blending controls

ROVER and ROVER LITE use a Siemens SIMATIC S7-1200 PLC for blending control in new and retrofit hot mix asphalt plants.

ROVER

  • Up to 4 aggregate feed bins
  • 1 asphalt pump and meter
  • 1 virgin aggregate weigh bridge
  • 1 asphalt additive channel (% of asphalt)
  • 1 mineral filler channel (gravimetric or volumetric)

ROVER LITE

  • Up to 4 aggregate feed bins
  • 1 asphalt pump and meter
  • 1 virgin aggregate weigh bridge

Available as a complete console.

Product specifications

Aggregate feed bin control
Feeder drives
Control for up to 4 bin feeders with variable-frequency (VFD), eddy-current or DC drives.
Start, stop and speed
24 V DC PLC start/stop control for VFDs, with 120 V AC plant connections through I/O isolation relays. Scaled 0–10 V speed reference corresponds to 0–100% speed.
Speed feedback
1,200-pulse-per-revolution (PPR) encoder feedback through the PLC’s built-in high-speed counter.
Operator display
VFD status and speed settings, calibrated feed rate in tons per hour (TPH), maximum TPH entry for rate calculation, and recurring no-flow indication on the alarm screen.
Asphalt pump and meter control
Pump drive
Control for one asphalt pump with a VFD, eddy-current or DC drive. The PLC uses 24 V DC for VFD start/stop and spray/divert control and interfaces with the 120 V AC plant through I/O isolation relays.
Speed and rate
Scaled 0–10 V reference for 0–100% speed. The PLC’s built-in high-speed counter reads a 1,200 PPR encoder. The operator display shows drive status, speed settings and the calibrated rate in TPH, with a maximum TPH entry for rate calculation.
Temperature
Asphalt temperature compensation with a Type J thermocouple input. Operators can adjust input scaling and offset on the touchscreen.
Calibration and alarms
Touchscreen setup and calibration assistance. Calibration defaults are based on a Viking KK225 2-inch pump or equivalent. Operators can configure the recurring out-of-tolerance alarm.
Virgin aggregate weigh bridge control
Weigh bridge inputs
One weigh bridge with 0–10 V analog load-cell input and belt speed from a 1,200 PPR encoder through the PLC’s built-in high-speed counter. A load-cell signal conditioner, such as an Action Pak, is optional.
Rate and moisture
Calibrated rate calculation and TPH display use belt speed feedback. Moisture compensation uses one percentage entered on the touchscreen. Composite moisture calculation from individual aggregates is unavailable.
Asphalt additive and mineral filler control (ROVER only)
Asphalt additive
One additive channel. The PLC calculates the dose as a percentage of asphalt.
Mineral filler
One filler channel with gravimetric or volumetric control. Mineral filler feeds directly into the mixing drum, bypassing the aggregate weigh bridge.
Drive control
Both channels support VFD, eddy-current and DC drives. VFD start/stop uses 24 V DC PLC control with 120 V AC plant connections through I/O isolation relays. Scaled 0–10 V speed reference corresponds to 0–100% speed.
Feedback and rate
Both channels use 1,200 PPR encoder feedback through the PLC’s built-in high-speed counter. The touchscreen shows drive status, speed settings and calibrated rate in TPH, and accepts maximum TPH for rate calculation.
PLC software and operator controls
Mix control
Mix temperature uses a Type J thermocouple input with touchscreen scaling and offset. Travel time from the aggregate weigh bridge to the asphalt spray point is adjustable from 60 to 120 seconds. Production tracking ends at the spray point.
Production overview
Shows all enabled ingredients and key production values. Daily, period and long-term totalizers can be reset individually. Mix and asphalt temperature trends display in °F or °C.
Operator settings
English or Spanish, US or metric units, °F or °C, and operator display settings.
Aggregate and asphalt settings
Set aggregate maximum TPH, weigh bridge moisture, travel time to the asphalt spray point and no-flow alarm enablement. Asphalt settings cover maximum TPH and temperature scaling and offset. Calibration assistance is available for both.
Diagnostics and alarm history
Digital and analog input and output lists, PLC and touchscreen health, and system and process alarm history.
Siemens PLC and I/O racks

SIMATIC S7-1200 main rack · Both models

Slot 1 · CPU 1214C
Compact DC/DC/relay CPU, 14 digital inputs at 24 V DC, 10 relay outputs rated 2 A and 2 analog inputs at 0–10 V DC. Supply: 20.4–28.8 V DC. Program and data memory: 150 KB.
Slot 1 · SB 1221 signal board
4 sourcing digital inputs, 24 V DC, 200 kHz.
Slot 2 · SM 1221
8 digital inputs, 24 V DC, sink or source.
Slot 3 · SM 1231
4 analog inputs: ±10 V, ±5 V, ±2.5 V, 0–20 mA or 4–20 mA. Resolution: 12 bits plus sign (13-bit ADC).
Slots 4 and 5 · SM 1232
Each module has 4 analog outputs: ±10 V at 14-bit resolution, or 0–20 mA or 4–20 mA at 13-bit resolution.
Slot 6 · SM 1231 TC
4 analog thermocouple inputs.
Slot 7 · PM1207 power module
Stabilized supply: 120/230 V AC input, 24 V DC output at 2.5 A.

Second I/O rack · ROVER only

Slot 1 · CPU 1211C
Compact DC/DC/relay CPU, 6 digital inputs at 24 V DC, 4 relay outputs rated 2 A and 2 analog inputs at 0–10 V DC. Supply: 20.4–28.8 V DC. Program and data memory: 75 KB.
Slot 1 · SB 1222 signal board
4 digital outputs, 24 V DC, 200 kHz.
PLC I/O isolation relays

ROVER and ROVER LITE use Phoenix Contact interposing relays to interface 120 V AC plant signals with 24 V DC PLC I/O. Isolation between the module input and switched contact helps reduce electrical noise coupling between the circuits.

Plant input relay
PLC-RSC-120UC/21 (2966197) handles 120 V AC plant input signals. The module’s nominal input rating is 120 V AC or 110 V DC.
PLC output relay
PLC-RSC-24DC/21 (2966171) accepts a 24 V DC command from the PLC and switches the plant-side circuit through an isolated contact.
Mounting and service
Both modules use screw terminals, one changeover contact (SPDT), and NS 35/7.5 DIN rail mounting. The plug-in electromechanical relay can be replaced separately from the PLC I/O module.
Siemens HMI display options

SIMATIC HMI Unified Comfort widescreen TFT panels support multi-touch or a wireless USB mouse and keyboard.

MTP700 (NOMAD)
7.0 inches, 800 × 480 pixels.
MTP1000
10.1 inches, 1280 × 800 pixels.
MTP1500
15.6 inches, 1366 × 768 pixels.

Other SIMATIC HMI Unified Comfort panels are available.

Plant interfaces and equipment options

Plant interface hardware

Ewon Cosy+ Ethernet
VPN gateway for remote access to the PLC, HMI or other connected devices through Talk2m.
Brainboxes SW-504
Unmanaged industrial Ethernet switch, four 10/100 ports, DIN rail mounting and dual redundant 5–30 V DC inputs.
ROVER cable set
25-foot cable set using LAPP KABEL and Belden cables.

Optional equipment

Load-cell signal conditioner
Optional. Listed suppliers: Allen-Bradley, Absolute Process Instruments and Omega Engineering.
COSTA Industrial tach encoders
Optional.
Other listed options
Cables, load cells and asphalt valve position limit switches. Ask about availability for your configuration.
Discuss your plant with Rick

02 / Other equipment

Equipment and service

  • Liquid asphalt transfer equipment for ISO tanks
  • Asphalt calibration tanks and scales
  • Asphalt heating equipment and parts
  • Pumps and motors
  • Electrical controls and parts
  • Installation and service
CAD rendering of an industrial pump and motor assembly with a yellow safety guard
Pump assembly / CAD
Three blue industrial pump and motor assemblies with yellow safety guards
Pump + motor assemblies
Six industrial oil burner assemblies with blue hoses arranged on a workshop floor
Oil burners

03 / Direct contact

Talk with Rick Costa

Run your plant specs by Rick before you order. His advice draws on more than 40 years in the industry.

COSTA Industrial

© 2026 COSTA Industrial LLC

Miami, FL / Chattanooga, TN

Photo